RPICT4W3T1
  • RPICT4W3T1
  • RPICT4W3T1
  • RPICT4W3T1
  • RPICT4W3T1

RPICT4W3T1

RPICT4W3T1

RPICT4W3T1 - Raspberrypi AC current and voltage hat

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Sensors and Raspberrypi are not included.

Rating (A)
3Phase Voltage Method
£75.00
VAT excluded
Quantity
In Stock
7 Items

Description

 

 
 

RPICT4W3T1

Raspberrypi AC current and voltage hat



Online Documentation


  • 4x AC Current Ports.
  • 3x AC Voltage Ports.
  • 1 Temperature Port
  • Provides Irms, Vrms, RealP, ApparentP, ReactiveP, PFactor, Frequency, EstimatedP.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Power combinations configurable (Current-Voltage pairing).
  • Open Source Arduino Firmware.
  • Stackable with RPICT8 Slave.

Package Content

  • 1 RPICT4W3T1 Unit.
  • 4 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Current:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Temperature:

  • DS18B20


Technical Specifications

Microcontroler Atmel Atmega328p
MCU Frequency 16Mhz
Operating Voltage 5V
Waveform Sampling 4400sps
Fastest Data Polling 800ms (for 4 channels)
Vertical Resolution 12 bits (4096 steps)
Communication UART Serial Port
Firmware Arduino (open source)
Dimensions 100x65mm
Programming port 6 pin ISP
Compatible OS Any supporting GPIO serial port access
Compatible Raspberrypi All of Family 1,2,3,4 and Model A, B
Compatible CT Current output type
AC Current Range Options from 20A to 600A
AC Voltage Range Options from 140V to 430V
Smallest Readable Current Approx 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

 

Product Details
RPICT4W3T1
7 Items

4 other products in the same category:

RPICT7V1 Master Version 6

Reference: RPICT7V1_LUMU

RPICT7V1 Master Version 6

RPICT7V1 - Raspberrypi AC current and voltage hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support for the voltage port. Sensors and Raspberrypi are not included. Earlier version can be found here. RPICT7V1 VERSION 5.
£48.00
More RPICT7V1 Master Version 6
In Stock
RPIZ_CT3V1

Reference: RPIZ_CT3V1_WSZQ

RPIZ_CT3V1

RPIZ_CT3V1 - 3 CT and 1 Voltage AC adaptor for Raspberrypi zero. Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support for the voltage port. Sensors and Raspberrypi are not included. Documentation
£17.50
More RPIZ_CT3V1
In Stock
RPICT3V1_RLY2

Reference: RPICT3V1_RLY2_BJQJ

RPICT3V1_RLY2

Raspberrypi CT Adaptor Connect up to 3 Current and 1 voltage sensors to a raspberrypi. 2 250V/120V relays,
£33.00
More RPICT3V1_RLY2
In Stock
RPIZ_CT3T1

Reference: RPIZ_CT3T1_TUPJ

RPIZ_CT3T1

RPIZ_CT3T1 - 3 CT and 1 Temperature AC adaptor for Raspberrypi zero. Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Sensors and Raspberrypi are not included. Documentation
£17.50
More RPIZ_CT3T1
Last items in stock

You might also like

Enclosure Kit for RPICT4V3

Enclosure Kit for RPICT4V3

Enclosure Kit for RPICT4V3 Package includes 3x 3D printed Parts 4x M3 Screws 4x M3 Nuts Note. 3D printed parts are fragile. Handle with care.
£15.00
More Enclosure Kit for RPICT4V3
In Stock
RPICT8 slave Version 5

Reference: RPICT8_slave_WYDZ

RPICT8 slave Version 5

Connect up to 8 Current sensors to a Raspberrypi. This is the slave version of the RPICT8 this can only work with a master RPICT board version 5 such as RPICT8 or RPICT7V1 or RPICT4V3. Package includes slave stand off for mounting onto master board.
£30.00
More RPICT8 slave Version 5
In Stock
Slave Standoff - Pack of 4

Slave Standoff - Pack of 4

Male/Female stand off to mount slave board. For the following boards: RPICT7V1 version 3 RPICT4V3 version 3 RPICT8 version 3 This is for a pack of 4 standoff. Note: * These are only needed if you plan to stack boards together. All RPICT board come with standoff included. * You do not need these if you have ordered a slave board.
£2.00
More Slave Standoff - Pack of 4
In Stock
ZMPT 1X Voltage Sensor

Reference: ZMPT_1X_JPLG

ZMPT 1X Voltage Sensor

ZMPT101B Module. Convert AC Voltage to lower AC Voltage for use with RPICT series. Power Jack 2.1mm cable provided. Length 0.5m.
£12.00
More ZMPT 1X Voltage Sensor
In Stock