RPICT3T1
  • RPICT3T1
  • RPICT3T1
  • RPICT3T1
  • RPICT3T1
  • RPICT3T1

RPICT3T1

RPICT3T1_MURC

RPICT3T1 - Raspberrypi AC current hat with Temperature

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Sensors and Raspberrypi are not included.

Rating (A)
£19.00
VAT excluded
Quantity
In Stock
65 Items

Description

 

 
 

RPICT3T1

Raspberrypi AC current hat with temperature



Online Documentation


  • 3x AC Current Ports.
  • 1x Temperature Ports.
  • Provides Irms, EstimatedPower, Temperature.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.

Package Content

  • 1 RPICT3T1 Unit.
  • 2 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Temperature:

Current:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

Microcontroler Atmel Attiny84
MCU Frequency 8Mhz
Operating Voltage 3.3V
Waveform Sampling 2500sps
Fastest Data Polling 600ms
Vertical Resolution 10 bits (1024 steps)
Communication UART Serial Port
Firmware Arduino (open source)
Dimensions 56x35mm
Programming port 6 pin ISP
Compatible OS Any supporting GPIO serial port access
Compatible Raspberrypi All of Family 1,2,3,4 and Model A, B
Compatible CT Current output type
AC Current Range Options from 20A to 600A
Max Temperature probes 8
Smallest Readable Current Approx 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

 

Product Details
RPICT3T1_MURC
65 Items

4 other products in the same category:

RPIZ_CT3V1

Reference: RPIZ_CT3V1_WSZQ

RPIZ_CT3V1

RPIZ_CT3V1 - 3 CT and 1 Voltage AC adaptor for Raspberrypi zero. Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support for the voltage port. Sensors and Raspberrypi are not included. Documentation
£17.50
More RPIZ_CT3V1
In Stock
RPICT4W3T1

Reference: RPICT4W3T1_UWWM

RPICT4W3T1

RPICT4W3T1 - Raspberrypi AC current and voltage hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Sensors and Raspberrypi are not included.
£70.00
More RPICT4W3T1
In Stock
CT Conditioner

Reference: CTC01

CT Conditioner

Current Transformer Conditioner Connect most CT to an Arduino using the CT conditioner. Documentation
£10.00
More CT Conditioner
In Stock
RPICT4T4 Version 5

Reference: RPICT4T4_HJEO

RPICT4T4 Version 5

Connect up to 4 Current and 4 temperature sensors to a RaspberryPi
£38.00
More RPICT4T4 Version 5
In Stock

You might also like

DS18B20 Junction Board

Reference: DS18_JUNCT01

DS18B20 Junction Board

Junction board for DS18B20 sensors. Allow to connect up to 8 DS18B20 probe directly onto screw terminals. Board can be daisy chained to extend the number of connection. Compatible with our DIN rail mounts. Package includes * 1 DS18B20 Junction Board * 1 20cm 3way cable for connection with RPICT series.
£7.00
More DS18B20 Junction Board
In Stock
Enclosure Kit for RPICT3T1

Enclosure Kit for RPICT3T1

Enclosure Kit for RPICT3T1 Package includes 3x 3D printed Parts 4x M3 Screws 4x M3 Nuts Note. 3D printed parts are fragile. Handle with care.
£15.00
More Enclosure Kit for RPICT3T1
In Stock