• New
RPICT4V3 Master Version 6
  • RPICT4V3 Master Version 6
  • RPICT7V1 Master Version 6

RPICT4V3 Master Version 6

RPICT4V3_XXXX

RPICT4V3 - Raspberrypi AC current and voltage hat

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Voltage Sensor Type: Choose the desired support for the voltage port.

Sensors and Raspberrypi are not included.

Earlier version can be found here. RPICT4V3 VERSION 5.

Rating (A)
Voltage Sensor Type
£48.00
Quantity
In Stock

Description

 

RPICT4V3 Version 6

Raspberrypi AC current and voltage hat



Online Documentation


  • 4x AC Current Ports.
  • 3x AC Voltage Ports.
  • Provides Irms, Vrms, RealP, ApparentP, ReactiveP, PFactor, Frequency, EstimatedP.
  • Supports 3 Phase.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.
  • Stackable with RPICT8 Slave.

Package Content

  • 1 RPICT4V3 Unit.
  • 4 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Voltage:

Current:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

Microcontroler Atmel AVR32DB32
MCU Frequency 24Mhz
Operating Voltage 5V
Waveform Sampling 5500sps
Fastest Data Polling 1400ms (all 7 channels)
Vertical Resolution 12 bits (4096 steps)
Communication UART Serial Port
Firmware Arduino (open source)
Dimensions 56x65mm
Programming port 6 pin ISP
Compatible OS Any supporting GPIO serial port access
Compatible Raspberrypi All of Family 1,2,3,4,5 and Model A, B
Compatible CT Current output type
AC Current Range Options from 20A to 600A
AC Voltage Range Options from 140V to 280V
Smallest Readable Current Approx 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

 

Product Details
RPICT4V3_XXXX
50 Items
4 other products in the same category:
RPICT8 Version 4 Quick view

Reference: RPICT8_V4

RPICT8 Version 4

Raspberrypi CT Adaptor Connect up to 8 Current to a raspberrypi. High precision version of the RPICT8 using Instrumentation amplifiers. Both Current and Voltage CT are supported. Documentation
Price £95.00
More
In Stock
RPIZ_CT3T1 Quick view

Reference: RPIZ_CT3T1_TUPJ

RPIZ_CT3T1

RPIZ_CT3T1 - 3 CT and 1 Temperature AC adaptor for Raspberrypi zero. Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Sensors and Raspberrypi are not included. Documentation
Price £17.50
More
In Stock
RPICT3V1T1 Quick view

Reference: RPICT3V1T1_XASY

RPICT3V1T1

RPICT3V1T1 - Raspberrypi AC current, voltage and temperature hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support for the voltage port. Sensors and Raspberrypi are not included.
Price £20.00
More
In Stock
New 5A Conditioner for RPICT Quick view

5A Conditioner for RPICT

5A Conditioner This is an adaptor board to allow RPICT Series Version 6 to monitor 5A output CT's. This product requires 3.5mm stereo jack to connect to the RPICT card (not included)
Price £22.00
More
In Stock
You might also like
RPICT8 slave Version 5 Quick view

Reference: RPICT8_slave_WYDZ

RPICT8 slave Version 5

Connect up to 8 Current sensors to a Raspberrypi. This is the slave version of the RPICT8 this can only work with a master RPICT board version 5 such as RPICT8 or RPICT7V1 or RPICT4V3. Package includes slave stand off for mounting onto master board.
Price £30.00
More
In Stock