RPICT4V3 Master Version 5
  • RPICT4V3 Master Version 5
  • RPICT4V3 Master Version 5

RPICT4V3 Master Version 5

RPICT4V3_MXUL

RPICT4V3 - Raspberrypi AC current and voltage hat

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Voltage Sensor Type: Choose the desired support for the voltage port.

Sensors and Raspberrypi are not included.

Rating (A)
Voltage Sensor Type
£38.00
VAT excluded
Quantity
In Stock
54 Items

Description

 

 
 

RPICT4V3 Version 5

Raspberrypi AC current and voltage hat



Online Documentation


  • 4x AC Current Ports.
  • 3x AC Voltage Ports.
  • Provides Irms, Vrms, RealP, ApparentP, ReactiveP, PFactor, Frequency, EstimatedP.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Power combinations configurable (Current-Voltage pairing).
  • Open Source Arduino Firmware.
  • Stackable with RPICT8 Slave and RPICT4V3 Slave
  • Computes 3 phase power.

Package Content

  • 1 RPICT4V3 Unit.
  • 4 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Voltage:

Current:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

Microcontroler Atmel Atmega328p
MCU Frequency 16Mhz
Operating Voltage 5V
Waveform Sampling 4400sps (1700sps in 3 phase)
Fastest Data Polling 800ms (for 4 channels)
Vertical Resolution 12 bits (4096 steps)
Communication UART Serial Port
Firmware Arduino (open source)
Dimensions 56x65mm
Programming port 6 pin ISP
Compatible OS Any supporting GPIO serial port access
Compatible Raspberrypi All of Family 1,2,3,4 and Model A, B
Compatible CT Current output type
AC Current Range Options from 20A to 600A
AC Voltage Range Options from 140V to 280V
Smallest Readable Current Approx 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

 

Product Details
RPICT4V3_MXUL
54 Items

4 other products in the same category:

5A CT Signal Conditioner Board for RPICT Series | LeChacal

5A Conditioner for RPICT

5A Conditioner This is an adaptor board to allow RPICT Series Version 6 to monitor 5A output CT's. This product requires 3.5mm stereo jack to connect to the RPICT card (not included)
£22.00
More 5A Conditioner for RPICT
In Stock
RPICT USB Adaptor

Reference: RPICT_USB

RPICT USB Adaptor

RPICT USB Adaptor Connect any RPICT unit to the USB port of a computer or Raspberrypi. Package Include. * 1 RPICT USB Adaptor * 1 USB Cable
£15.00
More RPICT USB Adaptor
In Stock
RPICT4V3 slave Version 5

Reference: RPICT4V3_IDRT

RPICT4V3 slave Version 5

Connect up to 4 Current sensors and 3 Voltage sensors to a Raspberrypi. This is the slave version of the RPICT4V3 this can only work with a master RPICT board version 5 such as RPICT8 or RPICT7V1 or RPICT4V3. Package includes slave stand off for mounting onto master board.
£30.00
More RPICT4V3 slave Version 5
In Stock
OPICT8 for Orange Pi

Reference: OPICT8_LOMR

OPICT8 for Orange Pi

OPICT8 - Orange Pi AC current hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Sensors and Orange Pi are not included.
£38.00
More OPICT8 for Orange Pi
In Stock

You might also like

Enclosure Kit for RPICT4V3

Enclosure Kit for RPICT4V3

Enclosure Kit for RPICT4V3 Package includes 3x 3D printed Parts 4x M3 Screws 4x M3 Nuts Note. 3D printed parts are fragile. Handle with care.
£15.00
More Enclosure Kit for RPICT4V3
In Stock
ZMPT 3X Voltage Sensor

Reference: ZMPT_3X_IXKR

ZMPT 3X Voltage Sensor

ZMPT 3X Module. Convert AC Voltage to lower AC Voltage for use with RPICT series. Power Jack 2.1mm cable provided. Length 0.5m. Documentation Note not all RPICT units supports the ZMPT101B Module. Supported units are * RPICT7V1  RPICT4V3 Version 4 * RPICT7V1  RPICT4V3 Version 5 * RPICT7V1  RPICT4V3 Version 6 Range: For UK/EU type power lines use 280V. For...
£23.00
More ZMPT 3X Voltage Sensor
In Stock