• New
RPICT8 Master Version 6
  • RPICT8 Master Version 6
  • RPICT8 Master Version 6

RPICT8 Master Version 6

RPICT8_HCQL

RPICT8 - Raspberrypi AC current hat

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Sensors and Raspberrypi are not included.

Earlier version can be found here. RPICT8 Version 5.

Rating (A)
£48.00
Quantity
In Stock

Description

 

RPICT8 Version 6

Raspberrypi AC current hat



Online Documentation


  • 8x AC Current Ports.
  • Provides Irms, EstimatedP, Frequency.
  • View/record data using Linux / Python / Emoncms / Grafana / MQTT and more.
  • Configurable from serial port.
  • Open Source Arduino Firmware.
  • Stackable with RPICT8 Slave and RPICT4V3 Slave

Package Content

  • 1 RPICT8 Unit.
  • 4 Mounting Stand off with screws.
The listing does not include sensors and Raspberrypi.

Recommended Sensors

Current:

(for any other CT sensor please contact us to have adapted resistor mounted and calibration coefficients calculated)

Technical Specifications

Microcontroler Atmel AVR32DB32
MCU Frequency 24Mhz
Operating Voltage 5V
Waveform Sampling 9090sps (5000sps if combined with a voltage port)
Fastest Data Polling 1600ms (all 8 channels)
Vertical Resolution 12 bits (4096 steps)
Communication UART Serial Port
Firmware Arduino (open source)
Dimensions 56x65mm
Programming port 6 pin ISP
Compatible OS Any supporting GPIO serial port access
Compatible Raspberrypi All of Family 1,2,3,4 and Model A, B
Compatible CT Current output type
AC Current Range Options from 20A to 600A
AC Voltage Range Options from 140V to 280V
Smallest Readable Current Approx 50mA to 150mA

Scope of Use

This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

 

Product Details
RPICT8_HCQL
8 Items
4 other products in the same category:

Reference: RPIWA_CT4V3

RPIWA_CT4V3

CONTACT US FIRST TO PURCHASE THIS PRODUCT. WE RECOMMEND THIS PRODUCT BELOW INSTEAD FOR FIRST TIME USE: RPICT4V3 RPIWA_CT4V3 - Raspberrypi AC current and voltage hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support...
Price £45.00
More
Product available with different options

Reference: CTC01

CT Conditioner

Current Transformer Conditioner Connect most CT to an Arduino using the CT conditioner. Documentation
Price £10.00
More
In Stock

Reference: RPIZ_CT4V3T2_VENW

RPIZ_CT4V3T2 - piZero

Raspberrypi ZERO CT AdaptorConnect up to 4 Current and 3 voltage AC. Also support for DS18B20 temperature sensors and RTD Thermocouples. Documentation. Sensors on picture and Raspberrypi not included. Package includes: * RPIZ_CT4V3T2 board * MAX31865 module mounted (RTD) * 4 stand off. * 5x2 connector to solder on Raspberrypi. * Molex connector for DS18B20.
Price £50.00
More
In Stock

Reference: RPICT4V3_XXXX

RPICT4V3 Master Version 6

RPICT4V3 - Raspberrypi AC current and voltage hat Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other". Voltage Sensor Type: Choose the desired support for the voltage port. Sensors and Raspberrypi are not included. Earlier version can be found here. RPICT4V3 VERSION 5.
Price £48.00
More
In Stock
You might also like

Reference: RPICT8_slave_WYDZ

RPICT8 slave Version 5

Connect up to 8 Current sensors to a Raspberrypi. This is the slave version of the RPICT8 this can only work with a master RPICT board version 5 such as RPICT8 or RPICT7V1 or RPICT4V3. Package includes slave stand off for mounting onto master board.
Price £30.00
More
In Stock