> >>RPICT7V1 Version 3
Prix réduit ! Raspberrypi 7x Current Sensor Adaptor - 1 Voltage - emoncms Agrandir l'image
Précédent Suivant

RPICT7V1 Version 3

Neuf

Connect up to 7 Current and 1 voltage sensors to a Raspberrypi.

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Master Kit:
Contain one RPICT board with 4 master stand off and microcontroller included.
Slave Kit:
Contain one RPICT board with 4 slave stand off without microcontroller.

Plus de détails

849 Produits

£ 29.00

-£ 6.00

£ 35.00

  • Master Kit
  • Slave Kit

Ajouter à ma liste d'envies

En savoir plus


RPICT7V1 version 3 - Raspberrypi CT Adaptor


IMG_1128_small.pngConnect 7 Current and 1 voltage sensors to a Raspberrypi



Documentation


  • 7x Current sensor ports
  • 1x ac Voltage sensor ports
  • Arduino IDE programmable
  • Output Active Power/ Apparent power/ Power Factor/ Irms/ Vrms
  • Text based serial output.
  • Atmega328p Microcontroller
  • View/record data using Linux/Python/Emoncms/Nodered/Grafana
  • Stackable - Up to 5 board stack on one Raspberrypi.
  • Compatible with Raspberrypi 2 & 3.

Package Content

  • 1 RPICT7V1 version 3 Unit.
  • 4 Mounting Stand off.
  • 8 Mounting Screws
Note: Raspberrypi and sensors are not included in this listing.

Recommended Sensors

  • Voltage: 77DB-06-09 77DE-06-09 77DA-10-09
  • Current: SCT-013-000 SCT-019 SCT-006 or any other current output CT.

Outputs 21 channels:

  • Real Power x7 (Watts)
  • Irms x7 (mAmps)
  • Vrms x1 (Volts)
(note apparent power can be calculated using Vrms*Irms.

Default Parameters:

* Node ID: 11

* Scan interval: 5 seconds

* Output: Space separated Values (Emonhub)


Default loaded sketch freely available on the wiki page.

Example Ouput (Emoncms):


Rpict7v1_channels_001.png

Stacking boards

IMG_0980_small.png
The RPICT7V1 version 3 can be stacked with other RPICT7V1 or RPICT4V3 or RPICT8 to expand the numbers of sensors supported. See more about stacking in the link below. Stacking Documentation


This development board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by LeChacal.com to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This
evaluation board/kit does not fall within the scope of the European Union directives regarding  electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.

Avis

Note 
28/01/2019

Great product, very easy to use!

Instructions are detailed, and once you figure out the few basic setup steps and terminology if you are not super familiar with electrical, it is quite easy to use. Got it work on a Pi3 and Orange Pi.

  • 1 personne(s) sur 1 ont trouvé ce commentaire utile.

Donnez votre avis

RPICT7V1 Version 3

RPICT7V1 Version 3

Connect up to 7 Current and 1 voltage sensors to a Raspberrypi.

Rating: Choose the maximum rms current in Ampere the board can support with the associated CT. For any custom setup please opt for "other".

Master Kit:
Contain one RPICT board with 4 master stand off and microcontroller included.
Slave Kit:
Contain one RPICT board with 4 slave stand off without microcontroller.

Accessoires